- Provides a strong, permanent bond to solid, rubber backed tile and LVT
- Environmentally safe
- Guaranteed against discoloration
- May be used for indoor installations over standard construction surfaces
- Product is FloorScore® certified by SCS
All substrates must be clean, dry, structurally sound, properly cured and free of dirt, oil, paint, old adhesive, wax, sealers and curing agents. General scouring with 20 grit or #3 1/2 open-coat sandpaper will remove most compounds. All loose materials must be vacuumed from the surface after scouring. The subfloor must be flat to a tolerance of 3/16” in a 10’ radius. Grinding concrete floors is preferred over the use of filling compounds. If filling/flattening compounds are used, they must be Portland-based cementitious material and have a compressive strength equal to or greater than 3000 psi when cured. When using cementitious materials, they must be rated for the moisture content in the concrete slab. Always use the highest rated materials for moisture because the moisture levels will change. Consult the cementitious manufacturer’s application directions. Use of Titebond 670 over lightweight concrete and all gypsum-based materials requires the use of acrylic-based concrete primer or equivalent prior to application of adhesive.
Installation: Wet Lay Method - Porous Substrates
Open time is between 10 and 30 minutes. Adhesive must transfer to backing in order to promote adhesion. Employ a 100 pound roller in both directions within one hour of installation to work out any air pockets and produce solid bonding. It is recommended to use water to remove adhesive spots, and clean tools when adhesive is still wet. Removal of dry adhesive may require mineral spirits or other solvents. Follow solvent manufacturer’s safety precautions.
Installation: Pressure Sensitive Method - Non-Porous Substrates
When using a 3/8” nap, coverage will be approximately 150 – 200 square feet per gallon, depending on the amount of pressure used to apply the adhesive. The adhesive offers adequate strength to bond an LVT floor as a pressure sensitive when given up to 72 hours of open time. Allow adhesive to dry until a firm touch does not transfer adhesive. Keep the adhesive free from dust and dirt during long open times. Dust and dirt will negatively affect strength.
When using a 1/16 x 1/32 x 1/32 trowel, coverage will be approximately 250 to 300 sq. ft. per gallon. Spread adhesive and let it become dry to touch, where there is no transfer to fingers. This will take approximately 35-90 minutes depending on temperature and humidity. Do not install floor before adhesive is ready. Installing product too soon can lead to slippage and gaps between pieces. Install LVT per manufacturer’s directions with no more than three hours of open time.
Wet adhesive can easily be cleaned up with a cloth dampened with water. If the adhesive has dried, use a cloth dampened with mineral spirits. Follow solvent manufacturer’s directions when working with solvents and other flammable materials. For specific cleaning instructions, call Franklin International Technical Service at 1.800.347.4583
Do not sand, scour or abrade any material that is suspected of containing asbestos fibers. Asbestos is known to cause cancer. Federal law requires that asbestos be handled by a licensed and certified hazardous materials contractor.
MOISTURE CONTENT LIMITATIONS: Concrete subfloors should be tested for moisture prior to installation. Moisture levels cannot be greater than 8 lbs./1000sq.ft./24 hours on a Calcium Chloride Test (ASTM F1869), or relative humidity (RH) of 90% or less when tested with an in situ probe (ASTM F2170). When installing directly over wood subfloors the moisture content of the subfloor should be 13% or less. Installation over single-layer wood subfloors is not recommended.
LIMITATIONS: Do not use over high alkaline concrete (over 9.0 pH). Do not use to bond two non-porous substrates unless using pressure sensitive method. Product must dry to build strength. Do not store below freezing. Use in well-ventilated area. Warranty covers subfloor moisture resistance but does not cover damage from flooding or other surface moisture contamination.
WARNING: EYE AND SKIN IRRITANT. Do not swallow. Do not allow eye contact or prolonged skin contact. FIRST AID:If swallowed, do not induce vomiting, contact physician. If eye contact occurs, flush eyes with water for 15 minutes. Wash skin contact areas with soap and water. If irritation from eye or skin contact areas persist, contact physician. For additional information, refer to Safety Data Sheet.
KEEP OUT OF THE REACH OF CHILDREN.
|Part No.||Size||Weight(lbs.)||UPC||Case UPC||Units Per Package||Packages Per Pallet
|9244||4 Gallon Plastic Pail||43.74||037083092448|| ||1||36
|9246||Gallon Plastic Pail||45.00||037083092462|| ||4||30
Franklin International will honor the applicable terms of any resilient floor manufacturer’s current published adhesive warranty or subfloor moisture warranty (where applicable) when the flooring was installed using Titebond 670 Resilient Flooring Adhesive in accordance with product instructions and the instructions of the resilient floor manufacturer.*
Franklin International will also warrant Titebond 670 to be free from defects in materials and workmanship for a period of one year from the date of manufacture, if the product has been installed in accordance with the Franklin Specification Guide and the installation instructions furnished with the product. In the event of loss of adhesion of Titebond 670 due to product defect, Franklin International will reimburse the customer for the cost of labor and materials necessary to repair or replace the affected area(s) of the installed resilient flooring.
* Any and all addendums or changes to the vinyl floor manufacturer’s warranties will be reflected in the execution of Franklin International’s warranty immediately upon release by the vinyl floor manufacturer. The effective date of said changes and addendums will dictate coverage by Franklin International in relations to the date of installation.
As Franklin International is honoring the applicable terms of all vinyl floor manufactures’ current published warranties, Franklin International will also require the same jobsite preparations and installation instructions that accompany each warranty in question.