 |
|
|
|
Physical Properties (Typical) |
|
| Type Polyurethane |
|
Calculated VOC (less water): 1.1 g/L |
| State Solid |
|
Weight/gallon 9.7 lbs. |
| Color Translucent |
|
Flashpoint N/A |
| Dried film Opaque white |
|
Freeze/thaw stability Will not freeze |
| Solids 100% |
|
Viscosity 11,000 cps @ 250°F. |
| Storage life12 months in unopened foil pouch. 4 weeks after opened. |
|
|
|
|
|
Application Guidelines |
|
Application temperature 250°F.
Service temperature -20 °F. to 275 °F.
Method of application HiPURformer™ adhesive applicator
|
| The HiPURformer Advanced Bonding System utilizes the patented, innovative hot melt adhesive applicator from German manufacturer Steinel. This high quality tool provides the perfect delivery system for HiPURformer adhesives. It is cordless, lightweight and extremely easy to use. |
 |
|
Coverage Approximately 71 linear feet of 1/16" (OD bead) per 50 gram cartridge
Working surfacesSurfaces must be dry and free from any dust, dirt or other material that may deter adhesion. Apply adhesive using the HiPURformer adhesive applicator. Join the surfaces to be bonded together, ensure proper alignment of pieces and hold firmly in place until the adhesive sets (approximately 5 minutes).
Cleanup Allow any squeeze out to become firm and remove it with a putty knife or scraper. Fully cured material must be removed by sanding or cutting. Do not use heat or flame to remove adhesive.
Bond Strength at room temperature
| Time |
Strength psi |
|
| 10 min |
118 |
| 1 hr. |
478 |
| 24 hrs. |
1016 |
Important:To prolong the shelf life after initial use, extrude a one-inch bead of adhesive to purge any air from the cartridge tip, then immediately replace the cartridge cap tightly, while the adhesive is hot. ALWAYS WEAR GLOVES.
|
|
|
|
Product Features |
|
High-strength, permanent bonds
Interior/Exterior - Passes ANSI/HPVA Type I testing - Waterproof
Adheres to wood, melamine, PVC, ABS, ceramics, metals and most common substrates
Greatly reduces or eliminates mechanical fasteners in many applications
Solvent free and nonflammable
Versatile performance
Long set time - Ideal for face frames and intricate assemblies
Woodworking, finish carpentry, construction, repair
UV indicator for easy cleanup
|
|
|
|
Limitations |
|
Not for continuous submersion or use below the waterline. Substrates that oxidize, such as copper and brass, must be abraded prior to bonding. |
|
|
|
Caution Statement |
|
WARNING: Eye and Skin Irritant. Potential Skin and Respiratory Sensitizer. Caution: Contact with heated product may cause thermal burns. Always wear gloves. Contains isocyanates. Avoid contact with skin and eyes. Avoid prolonged or repeated contact with vapors. Do not swallow. May be harmful if swallowed. First Aid: If swallowed, do not induce vomiting. Call physician immediately. If eye contact occurs, flush eyes with water for 15 minutes and call physician. In case of skin contact, wash skin with soap and water. Seek medical attention if sensitization or rash occurs. If inhaled, move to fresh air and contact physician. For additional safety information, refer to Material Safety Data Sheet or call 1-800-347-4583.
KEEP OUT OF THE REACH OF CHILDREN. |
|
|
|
Ordering Information |
|
| Cat. No. |
Size |
Units per
Package |
Weight |
Packages
per Pallet |
|
| 1351 |
50 gram Cartridge |
10 |
2 |
120 |
| 1361 |
HiPURformer Adhesive Applicator |
6 |
12 |
40 |
|
|
|
|
Important Notice: Our recommendations, if any, for
the use of this product are based on tests believed to be reliable. Since the use of this product is beyond
the control of the manufacturer, no guarantee or warranty, expressed or implied, is made as to such use or
effects incidental to such use, handling or possession or the results to be obtained, whether in accordance
with the directions or claimed so to be. The manufacturer expressly disclaims responsibility therefore.
Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict
with existing laws and/or patents covering any material or use. |
©1999 Franklin International