 |
|
|
|
Physical Properties (Typical) |
|
| Type Polychloroprene latex |
|
Calculated VOC (less water):0.0 g/L |
| State Liquid |
|
Weight/gallon 9.2 lbs. |
| Color Blue/green and neutral/clear |
|
Flashpoint >200°F |
| Solids 55% |
|
Freeze/thaw stability Not freeze/thaw stable |
| Viscosity 2,000 cps |
|
Storage life 12 months in tightly closed containers at 75°F. |
|
|
|
|
Application Guidelines |
|
Application temperature 60°F. to 90°F.
Service temperatures -20°F. to 200°F.
Method of application Brush, roller or spray gun
Coverage 533 sq. ft. per gallon on single surface coverage; 266 sq. ft. per gallon for bonded surfaces (3 wet mils)
640 sq. ft. per gallon on single surface coverage; 320 sq. ft. per gallon for bonded surfaces (2.5 wet mils)
763 sq. ft. per gallon on single surface coverage; 382 sq. ft. per gallon for bonded surfaces (2.09 wet mils)
Working time Up to 2 hours
Working surfaces Surface must be clean and dry of any material that may deter adhesion. Sand nonporous surfaces. Store adhesive at 60°F. or higher for 24-48 hours before use. Cut and fit all materials before applying adhesive. Apply a liberal coat of adhesive to both surfaces. Allow adhesive to dry before bonding surfaces. Position surfaces carefully before assembly because bonding is immediate upon contact. If surfaces do not bond immediately, the adhesive has been allowed to dry too long or not enough cement was used. In either case, repeat application. After assembly, roll entire bonding surface with a 3" wide roller. Trim and finish can be started immediately after bonding.
Cleanup Use warm, soapy water to clean tools and excess adhesive while wet. Remove dried adhesive with mineral spirits. Follow solvent vendor’s precautions when using solvents. NOTE: Test solvent in an out-of-the-way area to make sure it will not mar or attack the surface.
|
|
|
|
Product Features |
|
Superior bond strength
Environmentally safe - Zero-VOC
Bonds plastic laminates, veneers & post-forming
Easy water clean-up - Low odor
|
|
|
|
Limitations |
|
Do not use materials made with copper or copper alloys to store or apply GREENchoice Post-forming Neoprene Plus Contact Cement. Do not laminate materials made from copper or copper alloys with this adhesive. Do not use this product on vinyl due to plasticizer migration. KEEP FROM FREEZING. Recommended long term storage temperature is 40°F. to 95°F. |
|
|
|
Caution Statement |
|
CAUTION: EYE AND SKIN IRRITANT. POSSIBLE RESPIRATORY IRRITANT. Do not swallow. Do not allow eye contact or prolonged skin contact. Wear eye and skin protection. Avoid breathing vapors. Use only with positive cross-ventilation. Keep container closed when not in use. First Aid:If eye contact occurs, flush eyes with water for 15 minutes; contact physician immediately. Wash skin contact areas with soap and water; contact physician if irritation persists. If dizziness or other adverse effects are experienced, move to fresh air; contact physician if discomfort persists. If swallowed, do not induce vomiting; contact physician. For additional information, refer to Material Safety Data Sheet. KEEP OUT OF THE REACH OF CHILDREN. |
|
|
|
Ordering Information |
|
| Cat. No. |
Size |
Units per
Package |
Weight |
Packages
per Pallet |
|
| 3565 |
Neutral - Quart |
6 |
15.69 |
112 |
| 3566 |
Neutral - Gallon |
2 |
19.84 |
75 |
| 3567 |
Neutral - 5 Gallon |
1 |
48.8 |
24 |
| 3568 |
Neutral - 52 Gallon |
1 |
534.51 |
4 |
| 4645 |
Blue - Quart |
6 |
15.69 |
112 |
| 4646 |
Blue - Gallon |
2 |
19.84 |
75 |
| 4647 |
Blue - 5 Gallon |
1 |
48.8 |
24 |
| 4648 |
Blue - 52 Gallon |
1 |
534.51 |
4 |
|
|
|
|
Important Notice: Our recommendations, if any, for
the use of this product are based on tests believed to be reliable. Since the use of this product is beyond
the control of the manufacturer, no guarantee or warranty, expressed or implied, is made as to such use or
effects incidental to such use, handling or possession or the results to be obtained, whether in accordance
with the directions or claimed so to be. The manufacturer expressly disclaims responsibility therefore.
Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict
with existing laws and/or patents covering any material or use. |
©1999 Franklin International