 |
|
|
|
Physical Properties (Typical) |
|
| Resin (Part A) |
|
Hardener (Part B) |
| Weight/gallon9.18 lbs |
|
Weight/gallon8.24 lbs. |
| Viscosity260 cps |
|
Viscosity800 cps |
| Colorclear |
|
Coloramber |
| VOC165 g/L |
|
VOC84 g/L |
| Flashpoint105-110°F |
|
Flashpoint120°F |
| Storage Life1 year in closed container |
|
Storage Life1 year in closed container |
| Titebond 531 Mixture |
|
|
| Viscosity 340 cps |
|
Colorclear |
| Weight/gallon:8.59 lbs |
|
Mix ratio by volume100:80 |
| Calculated VOC132 g/L |
|
Mix ratio by weight100:69 |
| Pot life at 25°C30 min |
|
Tack Free Time4-6 hours @ 70°F |
|
|
|
|
Application Guidelines |
|
Subfloor Preparation
All substrates must be clean, dry, structurally sound, properly cured and free of dirt, oil, paint, old adhesive, wax, sealers and curing agents. General scouring with 20 grit or #3 1/2 paper will remove most compounds. After scouring, all loose materials must be vacuumed from the surface. Subfloor must be flat to a tolerance of 3/16" in 10'. Grinding concrete floors is recommended over using filling compounds. All filler/leveling compounds must be of Portland base and have a high compressive strength.
Concrete Surface Preparation
Concrete subfloors must be structurally sound and free of voids and cracks. Make repairs to concrete substrates to remove unsound or deteriorating areas. If needed, apply cementitious patch to any voids or cracks. Allow cementitious repair materials to cure per cementitious manufacturer’s recommendations. Lightweight concrete or gypsum-based subfloors/materials must have Titebond Concrete Primer (or equivalent) applied prior to use of Titebond 531. Follow directions of Titebond Concrete primer (or equivalent) before use.
Moisture Content Limitations
Gold Warranty Only: On-grade applications are subject to moisture and should be tested for moisture prior to installation. Titebond 531 should be used on all concrete substrates where a calcium chloride reading is below 12lbs./24hours/per 1000 square feet. Concrete subfloors with a reading over 12 lbs. must be allowed to dry out prior to using Titebond 531. Do not install Titebond 531 on below-grade installations. There are no moisture content limitations when terms of the Platinum Warranty have been met. Refer to warranty section for complete details.
Moisture Testing
Gold Warranty Only: A Calcium Chloride Test must be completed and recorded PRIOR to using the Titebond 531 for the Gold Warranty to be obtained. Concrete with greater than 12 lbs. of emission should be allowed to dry out before applying any floor covering unless terms of the Platinum Warranty have been met. No moisture testing is required when terms of the Platinum Warranty have been met. Refer to warranty section for complete details.
Ventilation
Titebond 531 contains solvent. Positive cross ventilation is required at all times. Extinguish all pilot lights and flames prior to mixing or applying.
Mixing Directions
DO NOT THIN. DO NOT HAND MIX. Begin mixing both components in the Part A pail using a power mixer (e.g. 1/2" drill and paint or plaster paddle). Mix thoroughly for two minutes. Once Titebond 531 is completely mixed, the working time is 30 minutes. The portions are pre-measured to assure optimal performance. DO NOT MODIFY OR ESTIMATE.
Application Directions
Apply Titebond 531 directly to a clean and dry surface. Minimum required coverage is 4 mils wet film thickness (400 sq. ft. per mixed gallon unit; 100 sq. ft. per mixed quart unit) for Gold Warranty and 6.5 mils wet film thickness (250 sq. ft. per mixed gallon unit; 62 sq. ft. per mixed quart unit) for Platinum Warranty. Apply with a 3/8" nap roller immediately after mixing. Pour a "wet-line" approximately 3" wide the length of the room and spread with a roller. The product may be used from a pan also. Avoid excessive pressure on the roller so that an adequate amount of material will be spread. Excessive pressure will thin the material application. For best results, when using gallon size, divide the area into 4 sections and use 1/4 of the mixed product in each section. Do not extend the coverage as this will result in a voided warranty. Working time is 30 minutes once completely mixed.
Application Conditions
For best results, do not apply Titebond 531 when the temperature is below 65°F. Temperatures below 65°F may lead to increased curing time. Additionally, applications below 65°F are subject to a phenomenon known as "blushing", which is an oily or waxy coating that can cover Titebond 531. If blushing occurs, it must be wiped with a solvent and allowed to dry. Follow solvent manufacturer’s directions when working with solvents and other flammable materials. Do not apply Titebond 531 if temperatures exceed 100°F. Applications exceeding 100°F will result in the product curing too quickly, which may jeopardize the quality of the bond to concrete.
Clean-up
Fresh coatings and tools can be cleaned with mineral spirits. Follow solvent manufacturer’s directions when working with solvents and other flammable materials.
Curing Time
Flooring may be installed over the Titebond 531 after the product is tack free or about 4 - 6 hours at 70°F. Be aware that temperatures below 65°F may increase curing time. Do not attempt to install flooring over Titebond 531 after 72 hours. If installation is delayed beyond 72 hours, the subfloor must be lightly abraded using a buffer. Clean the floor thoroughly before applying adhesive. For questions, call Franklin Technical Service at 1-800-347-4583.
Storage/Shelf Life
Store in a clean, dry environment above 60 °F. Shelf life is one year from date of manufacture.
Warranty
Please read Knowledge Base article 100527 for warranty information.
|
|
|
|
Product Features |
|
One self-contained package
Pre-measured portions to ensure proper mixing ratios
Complete installation directions on containers
Gallon size covers 400 square feet for Gold Warranty
Gallon size covers 250 square feet for Platinum Warranty
Quart size covers 100 square feet for Gold Warranty
Quart size covers 62 square feet for Platinum Warranty
Easy to mix and apply
Less expensive than vinyl
10 Year Residential Warranty; 5 Year Commercial Warranty
Cure time is approximately 4-6 hours at 70°F
Mold and mildew resistant
Adhesion promoter
Low odor
|
|
|
|
Limitations |
|
Do not install on below-grade installations
Do not apply below if temperatures exceed 100°F
Do not install flooring over Titebond 531 after 72 hours
Not to be partially mixed - follow the recommended directions |
|
|
|
Caution Statement |
|
WARNING. COMBUSTIBLE LIQUID AND VAPOR. VAPORS HARMFUL. Contains xylene. Keep away from heat, sparks, flame and other combustible materials. Use only with positive cross ventilation. Maintain ventilation until solvent dissipates. Do not use in confined areas. Use this product only if adequate ventilation can be used and maintained. Avoid breathing vapors. High vapor concentrations are irritating to the nose, throat, and respiratory system. Prolonged or repeated overexposure to solvents in product can cause central nervous system, peripheral nervous system, eye, skin, liver, kidney or respiratory system effects. Causes eye and skin irritation. Causes eye and skin irritation. May be absorbed through the skin. May cause allergic skin reaction. Harmful if swallowed. As when working with any solvent based material, appropriate personal protective equipment, including gloves, should be worn.FIRST AID: If dizziness or respiratory difficulty occurs, remove to fresh air. Seek medical attention if breathing difficulty continues. If swallowed, do not induce vomiting. Seek medical attention immediately. If eye contact occurs, flush eyes with water for 15 minutes and consult physician. For skin contact, wash with soap and water. Seek medical attention if irritation persists. For additional information, refer to Material Safety Data Sheet.KEEP OUT OF THE REACH OF CHILDREN. FOR PROFESSIONAL USE ONLY. |
|
|
|
Ordering Information |
|
| Cat. No. |
Size |
Units per
Package |
Weight |
Packages
per Pallet |
|
| 1285 |
1.0 Mixed Quart |
1 |
4 |
120 |
| 1286 |
1.1 Mixed Gallons Net |
1 |
13 |
32 |
|
|
|
|
Important Notice: Our recommendations, if any, for
the use of this product are based on tests believed to be reliable. Since the use of this product is beyond
the control of the manufacturer, no guarantee or warranty, expressed or implied, is made as to such use or
effects incidental to such use, handling or possession or the results to be obtained, whether in accordance
with the directions or claimed so to be. The manufacturer expressly disclaims responsibility therefore.
Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict
with existing laws and/or patents covering any material or use. |
©1999 Franklin International